FAQ: How To Install Stone On Fireplace Wall?

How do I put stone on my fireplace?

  1. measure to determine dimensions of fireplace. Determine the Size of the Mantel.
  2. prev. clamp 2×4 to existing mantel.
  3. prev. place new mantel on existing mantel.
  4. lay out stones to determine desired layout. Prep the Surface and Lay Out the Stones.
  5. mix up bucket of mortar. Mix the Mortar.
  6. prev. cut stones using wet saw.

How do you attach stacked stone to a fireplace?

How to Install Stacked Stone Fireplace

  1. Step 1: Measure the height of your fireplace. This will be based off of your preference for how you want your stone to look.
  2. Step 2: Measure the width.
  3. Step 3: Cut the stacked stone panels.
  4. Step 4: Mix mortar and install panel.
  5. 2 thoughts on “How to Install a Stacked Stone Fireplace

How much does it cost to put stone on fireplace?

Stone Fireplace Cost



A stone fireplace costs anywhere from $2,500 to $10,000 or more. Most range from $3,000 to $7,500 but a custom, real stone design built by a mason is pricier. Outdoor fireplaces cost $3,000 on average (though again, custom work will raise the price). Stone veneer is also known as “faux stone”.

You might be interested:  Often asked: How Do You Spell Taekwondo?

Can you use faux stone on fireplace?

Yes, the faux stone can be placed near a fireplace! If you have a zero clearance or gas fireplace, GenStone can typically be placed next to the unit.

Can you glue stone veneer to cement board?

What can I put stone veneer on for an interior application? For interior applications, stone veneer can be installed over cement board, drywall, and all of the above.

Can you install stacked stone on drywall?

Setting the Stone



Stone can be installed directly over other stable hard surfaces such as masonry, concrete blocks or brick, but may require a skim coat of mortar to even out the surface. Do not install stone directly on drywall or over painted surfaces.

What glue to use for stacked stone?

Tile adhesives or thinsets are rated for both interior only and interior/exterior work, so it is important to use a thinset or tile adhesive that meets the requirements of your installation, especially for wet applications. Norstone recommends using Laticrete tile adhesive.

How much does it cost to install ledger stone?

Cost to Install Stacked Stone Veneer

Stacked Stone Veneer Costs Zip Code
Basic Best
Stacked Stone Veneer – Material Prices $525.00 – $550.00 $625.00 – $650.00
Stacked Stone Veneer – Installation Cost $825.00 – $835.00 $950.00 – $1050.00
Stacked Stone Veneer – Total $1350.00 – $1385.00 $1575.00 – $1700.00

Can you grout stacked stone?

The three-dimensional veneer is made of cut pieces of natural stone that are attached to a backing and installed like you would tile. The material uses no grout; in fact, the dry stacked look is part of its appeal.

You might be interested:  Readers ask: How To Pick Wall Color?

How do you install cement board around a fireplace?

Add cement board to the entire area you’ll be tiling (for us, that means the floor and all 4 sides of the fireplace leaving room for wood mantle). On the ground and drywall, use thinset and screws to attach the cement board. But on the metal surround, use high heat adhesive to attach the cement boards.

How do you hang a mantel on a rock fireplace?

How To Hang A Wood Mantel on a Stone Fireplace using Rebar {before & after}

  1. Drill a hole in the stone fireplace using a mason drill bit.
  2. Cut the rebar to size.
  3. Fill hole with Fuz It (liquid nail)
  4. Insert the rebar into the hole on the stone and hold in place to allow liquid nail to grab rod.

How do you cut stacked stone panels?

The short answer is that stacked stone veneer panels are best cut using a combination of two tools – a wet saw designed to cut tile and stone, and a angle grinder for more precision and unique cuts.

Written by

Leave a Reply