FAQ: How To Install Wall Baseboard?

How do you attach baseboard to a wall?

Glue Baseboard to the Wall



Apply construction adhesive at the top and bottom. Nail the floor trim to the studs and then tack the braces to the trim with 1-inch brads. Force the gaps closed with the scrap and tack the blocks to the trim. Leave it overnight to let the adhesive set, and then pry the blocks free.

Should I glue or nail baseboards?

There’s no need to nail or glue them into place; just install the baseboard right over them, tight against the floor molding. It’s best to keep the nails at the bottom of the base above the gap so they go through drywall, not air.

What is the best way to install baseboards?

Using a miter box or a power miter saw, cut the baseboard at a 45-degree angle. Before nailing it in place, mark the second piece the same way, and test for fitting. Use 1-1/4″ or 1-1/2″ brads to close the corner. When you encounter the doorway, measure the distance between the door casing and the wall.

You might be interested:  Question: How Much Does It Cost To Build A Brick Wall?

What is needed to install baseboards?

You will need a few other tools and supplies to install baseboards. The handiest tool is a miter saw. A miter saw will help you quickly and accurately cut trim.



  1. Install shoe or cap moulding, if using.
  2. Caulk along the top edge and corner edges and nail holes.
  3. Touch up the baseboard with primer paint.

Can you glue baseboard to wall?

If you want to install baseboard you have two options: either use a good glue and stick them to the walls of the room, or use nails/screws to fasten them to the walls. We recommend you to choose the first option on drywall and the second one for masonry walls.

Do you need to nail baseboards into studs?

The general rule is to insert nails into the studs when another type of framing is not available. For example, chair rail molding, a decorative horizontal strip of trim that extends from wall to wall, requires nailing to the studs to hold it in place.

Can I install baseboards without nails?

Molding added to the home provides a finished look. Ideally, molding is fastened to the wall or cabinet with finishing nails for a tight and professional installation. There may be times when nailing is prohibitive, in which case you can install molding without nails using construction grade adhesive.

Can you install baseboard without a nail gun?

Installing it is as simple as buying a box of itty-bitty finishing nails and hammering in the molding. Seriously, you do not even need a nail gun. Here’s the whole step-by-step for how to install baseboards and crown molding—note that most of the work happens in the planning phase.

You might be interested:  Quick Answer: The Wall Game Show How To Enter?

Can you use Liquid Nails on baseboards?

These Liquid Nails products are rated for use with most interior trim and molding types.

How much should baseboard installation cost?

The labor cost to install baseboards is $4.90 to $7.75 per linear foot. Baseboard materials are pretty inexpensive (only about $0.80 to $1.20 per linear foot). Labor makes up most of your price.

What type of nail gun do I need for baseboards?

A finish nailer is a versatile tool, and drives either 15- or 16-gauge nails. They are used for smaller projects than framing nails, such as crown molding, baseboards, cabinets, chair rails, decorative trim, millwork, and hardwood flooring.

How long does it take to install baseboards?

Finish carpenters can install trim at the rate of about 20 linear feet per hour. A typical project requiring 125 linear feet of trim would take about 6.25 hours to install.

Do you install baseboards before or after flooring?

Baseboard Installation



Baseboards are often installed before flooring, since they must be finished in place with either stain or paint and this is much easier without worrying about staining the hardwood, tile or carpet.

Where do you nail baseboards?

Nail Baseboard to Wall



Set the scribed baseboard in place. Next, at each stud location, hammer two 8d finish nails through the board, at a slight downward angle, near its top and bottom edges. To avoid marking the wood, use a nail set to drive the heads just below the wood surface.

Written by

Leave a Reply