How To Cut Sheetrock On Wall?

What is the best tool to cut drywall?

There are three main types of drywall cutting tools: a utility knife, jab saw and drywall circle cutter. The simplest and most common way to cut drywall is by using a utility knife. These tools are durable, lightweight, easy to use and ergonomically designed. They’re also affordable and create little to no dust.

How do you cut a section of drywall?

Remove Damaged Section



Using a level, measure a straight line across the top and bottom of the damaged section. Then use a drywall knife to cut across those lines, stopping at studs that are past the broken areas. Continue cutting down the drywall adjacent to the studs until the entire section is removed.

How do you cut drywall without cutting studs?

Use a utility knife to score through the drywall. It will take several passes to get all the way through. Go slow, be careful, and don’t over cut at the ends. Only go 3/4″ onto the stud, going an inch or more could cause you to expose the whole stud and weaken the drywall on the opposite side.

You might be interested:  Readers ask: What Is Aikido Airma?

Can I use a rotary tool to cut drywall?

Multipurpose Cutting Bit: 561



The Dremel 561 cuts hard wood up to 3/8″ and soft wood up to 5/8″. Also cuts plastics, fiberglass, drywall, laminate, aluminum and vinyl siding.

What are the 5 cutting tools?

  • Fabric Shears. These will be one of your most used and important cutting tools for sewing.
  • All-Purpose (Cheap) Scissors.
  • Thread Snippers.
  • Embroidery Scissors.
  • Rotary cutters.
  • Pinking Shears.
  • Left-Handed Scissors.
  • Seam Rippers.

Does drywall have to end on stud?

Your drywall should end on stud or be butted up in the center with another piece of drywall. Either cut your drywall or add more studs. There is absolutely nothing wrong with 17-19″ on center which sounds like about 3 studs per sheet. I have run into this with old houses.

How many screws go into a 4×8 sheet of drywall?

How Many Screws Per Sheet of Drywall. Use about 32 drywall screws per sheet of 4-foot by 8-foot drywall installed horizontally on a wall. This total is comprised of four screws on the five middle studs and six screws on each of the two sides.

How do you reduce dust when cutting drywall?

For cutting installed drywall, I recommend a jab saw.



Further minimize dust by fitting the jab saw (view example on Amazon) with a metal-cutting blade, which has fine teeth that won’t remove as much material as a comparatively coarse standard blade.

Does Home Depot cut drywall for you?

Home Depot will cut both wood and sheetrock to you specifications when you purchase it at their stores. A few cuts are normally free, but if you have an extensive cutting requirement, they may charge extra.

You might be interested:  What Is Taekwondo Game?

Should drywall touch the floor?

Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods.

Do you cut drywall from the front or back?

Here’s how to go about it.

  1. Step 1: Score Front of Drywall Panel.
  2. Step 2: Break Drywall Sheet Along Scored Line.
  3. Step 3: Cut Through Paper on Back of Drywall Sheet.
  4. Step 4: Smooth Cut Edge of Drywall with Rasp.
  5. Step 1: Mark Drywall for Cutout Using Electrical Box.
  6. Step 2: Cut Electrical Box Opening with Drywall Keyhole Saw.

What is the difference between sheetrock and drywall?

Drywall is a flat panel made of gypsum plaster sandwiched in between two sheets of thick paper. It adheres to metal or wood studs using nails or screws. Sheetrock is a specific brand of drywall sheet. These terms are often used interchangeably.

Written by

Leave a Reply