- 1 How do you cut a floor against a wall?
- 2 How do you cut a subfloor under a wall?
- 3 How do you cut out an old subfloor?
- 4 What is a toe kick saw used for?
- 5 How do you cut concrete in tight spaces?
- 6 How do you fix wood rot in walls?
- 7 How much does it cost to replace bathroom subfloor?
- 8 Can I put new subfloor over old subfloor?
- 9 Is it easy to replace subfloor?
- 10 How do you cut a toe kick?
- 11 How do you remove a toe kick?
How do you cut a floor against a wall?
A reciprocating saw with a 6″ blade would easily let you cut right up to the base of the wall. You would just have to hold it at an angle to control the cutting depth so you don’t cut into the floor joists. It can be a little tricky to start the cut, especially in the corners, but it’s doable.
How do you cut a subfloor under a wall?
Cut Away the Subfloor
Set the circular saw to the proper depth to cut only the subfloor but none of the materials below the subfloor. The circular saw cannot cut flush with the wall, so cut as close as you can get to it. Most circular saws will let you cut as close as an inch or two.
How do you cut out an old subfloor?
Start at the end of one of a chalk line and cut the line with the saw. Repeat this and cut the remaining chalk lines on the subfloor. Make sure that each cut bypasses the intersection of an adjacent cut 1 inch to cut completely through the subfloor at the corners of the section. Remove the section of plywood.
What is a toe kick saw used for?
ideally if existing flooring or plywood being removed runs under cabinets or drywall. Additionally, toe kick saws are used for underlayment removal often found in kitchens that may have vinyl floors installed above.
How do you cut concrete in tight spaces?
Hand sawing and chain sawing is the way concrete is cut in tight spaces or to detail the work done by large saws. The hand saw can cut through concrete, brick, concrete pipes and manholes. The lighter weight saws are more portable and cost-effective for small jobs.
How do you fix wood rot in walls?
Replacing the Rot
Remove the rotted boards completely wherever possible. Cut out the rotted sections from boards that cannot be removed. Smaller sections of the rotted wood can be cut out with a rotary tool and an attached saw blade accessory. Cut boards of the same thickness and width as the boards you cut rot from.
How much does it cost to replace bathroom subfloor?
On average, replacing an entire subfloor in a 300-square-foot room can cost between $450 – $2,000.
Average Cost to Replace a Subfloor. (300 sq. ft)
Can I put new subfloor over old subfloor?
One of the benefits of removing the old flooring is it allows you the chance to fix any loose subflooring or squeaks by re-securing the main subfloor to the floor joists prior to installing the new flooring. With all that being said though the answer is YES you can install New Wood Flooring over the old.
Is it easy to replace subfloor?
The subfloor usually runs in a continuous sheet under all the walls. It can’t be removed easily. The underlayment, however, was put in after the walls were up, so it fits each room and is tailored to the type of floor covering being used. The underlayment, therefore, is easy to pull up and remove.
How do you cut a toe kick?
How to Cut a Toe Kick on Cabinets
- Measure the height between the floor and the bottom of the cabinet.
- Measure the length of the gap at the bottom of the cabinet.
- Mark on a piece of 1/4 inch plywood the two measurements of the cabinet gap.
- Cut the toe kick to length with a circular saw.
- Place the toe kick underneath the cabinet.
How do you remove a toe kick?
Position the end of the pry bar between the top of the quarter-round molding and the toe kick board. Tap the pry bar with a hammer to loosen the molding from the toe kick. Continue loosening the molding across the entire length and remove it from the toe kick.