- 1 Does it matter which way you hang Sheetrock?
- 2 Is it OK to hang drywall vertically?
- 3 Is there a difference between sheetrock and drywall?
- 4 How much space should be between sheets of drywall?
- 5 Should drywall touch the floor?
- 6 Can you use 1/2 inch drywall ceiling?
- 7 Does drywall have to end on stud?
- 8 How big of a gap can you fill with drywall mud?
- 9 Can you hang drywall on 24 centers on walls?
- 10 Should I drywall walls or ceiling first?
- 11 How do you install drywall for one person?
- 12 Will Home Depot cut sheetrock for you?
- 13 What can I use instead of drywall?
- 14 What causes nails to pop through drywall?
Does it matter which way you hang Sheetrock?
Drywall is typically stronger when hung in the long direction than it is in the short direction, which means less chance of sagging when attached perpendicular.
Is it OK to hang drywall vertically?
Commercial: Hang the drywall vertically. On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. Hides uneven studs – Hanging horizontally also allows the drywall to flow over the framing so that bowed studs create less of a problem.
Is there a difference between sheetrock and drywall?
Drywall is a flat panel made of gypsum plaster sandwiched in between two sheets of thick paper. It adheres to metal or wood studs using nails or screws. Sheetrock is a specific brand of drywall sheet. These terms are often used interchangeably.
How much space should be between sheets of drywall?
Unfortunately, there is no retroactive fix. However, during installation, be diligent about keeping that 1/8-inch space between sheets by using a guide. The blade of a drywall square is about 1/8-inch thick and does the trick.
Should drywall touch the floor?
Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods.
Can you use 1/2 inch drywall ceiling?
1/2–inch: Half-inch drywall panels are the standard thickness for interior walls, as well as ceilings. 5/8-inch: These panels are commonly used for ceilings, or for walls that require a prescribed fire-resistant rating.
Does drywall have to end on stud?
Your drywall should end on stud or be butted up in the center with another piece of drywall. Either cut your drywall or add more studs. There is absolutely nothing wrong with 17-19″ on center which sounds like about 3 studs per sheet. I have run into this with old houses.
How big of a gap can you fill with drywall mud?
Another situation that calls for filling is a drywall gap between sheets that’s more than about 1/2 inch wide. If you tape over a wide gap like this without filling it first, the tape will flex, and the joint compound covering it will chip away.
Can you hang drywall on 24 centers on walls?
You will not see any bowing or cupping with 5/8″ at 24” OC on walls. The second, and BEST option would be to install 3/4″ strapping 12″ OC across the field of the ceiling, and around the parameter. Ceiling screws should be no more than 16 inches apart.
Should I drywall walls or ceiling first?
Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. level. Irregularities less than 1/8 in.
How do you install drywall for one person?
Drywall hanging procedures
- Measure first ceiling panel length to center of joist. Hang panels perpendicular to framing.
- Shove cut end against wall and hoist into place. Notice 2×4 dead-man helps support heavy panels.
Will Home Depot cut sheetrock for you?
Home Depot will cut both wood and sheetrock to you specifications when you purchase it at their stores. A few cuts are normally free, but if you have an extensive cutting requirement, they may charge extra.
What can I use instead of drywall?
- Wood Planks. Wood planks are an age-old drywall alternative that has certainly stood the test of time well.
- Veneer Plaster. Veneer plaster might be the alternative that comes closest to traditional drywall.
- Lath & Plaster.
- Plywood and Sheet Wood.
- Texture Wall Panels.
- Brick & Masonry.
- Exposed Concrete Block.
- Cement Board.
What causes nails to pop through drywall?
Nail pops are largely due to wood or drywall movement and often appear within a year of construction. The result is a tiny bulge on the wall surface or, in some cases, a visible nail head if the drywall compound comes loose and falls away. This is the most common cause of nail pops and it’s completely cosmetic.