- 1 What does a wall thimble do?
- 2 What do you put on the wall behind a wood stove?
- 3 How do you replace a chimney thimble?
- 4 What is a fireplace thimble?
- 5 Can you run a wood stove pipe through a wall?
- 6 How close can I put my wood stove to the wall?
- 7 Can I use cement board behind my wood stove?
- 8 What material do you put behind a stove?
- 9 How do you seal a chimney thimble?
- 10 How do you fix a cracked flue thimble?
- 11 How do you cut a chimney flue?
- 12 Why is there a hole in my chimney?
- 13 Why is there a hole in my fireplace?
- 14 What is a Class A chimney system?
What does a wall thimble do?
Wall thimbles are an important component for venting stoves and other appliances since the thimble will insulate between the pipe and the wall, to protect drywall, wood frames and other materials from high temperatures and risk of fires.
What do you put on the wall behind a wood stove?
Common fireproof wall ideas for behind a stove include stone, brick and tiles. The look of a wood burning stove can be enhanced by using a faux panel (such as a stone veneer look) or using a fireback.
How do you replace a chimney thimble?
If the thimble is badly broken, you should knock out the pieces using a hammer and chisel. You should then spread fresh mortar around the circumference of the cleaned out hole and then set a new thimble into the hole.
What is a fireplace thimble?
The thimble is the round opening that can be found in a brick or stone chimney about five feet above floor level. The thimble enters the flue inside the chimney at a 90 degree angle and is designed to accommodate the entry of a stovepipe from a wood stove.
Can you run a wood stove pipe through a wall?
If you‘re setting up a wood-burning stove or pellet stove, running the chimney pipe through an outside wall saves the time and costs of installing a vertical chimney that requires a ceiling collar and roof flashing. For brick or stone walls, enlist a professional to cut the holes.
How close can I put my wood stove to the wall?
Wood frame walls covered with dry wall are considered combustible. If no wall protection is used, the common radiant-type stove or heater must be spaced out at least 36 inches from the wall.
Can I use cement board behind my wood stove?
A combustible floor must be protected by a non-combustible material (like tile, concrete board, or certified to UL-1618 or as defined by local codes) extending beneath the heater and a minimum of 6″ from each side and minimum 16″ from the front face of the stove and minimum 6″ (or the rear clearance to combustibles
What material do you put behind a stove?
Granite, stone and other natural or composite materials are also commonly used in backsplashes, whether in tile form or as larger pieces. These higher-end materials will mean an increase in budget, but also a stunning and long-lasting stove backsplash. Stainless steel is another popular option for stove backsplashes.
How do you seal a chimney thimble?
Lay a bead of cement, onto the end of the Thimble that butts against the masonry chimney. (See Figure 7) The cement will act as an adhesive and also seal the Thimble tightly to the masonry chimney should there be uneven surface. If the masonry chimney has a smooth surface the Cement will not be required.
How do you fix a cracked flue thimble?
To repair a crack, mix the mortar to a fairly watery consistency so that it’s easier to work into the cracks. Fill the cracks from both the inside and the outside of the thimble. Use refractory mortar, a special kind of mortar that is resistant to the high temperatures that will be present in a chimney thimble.
How do you cut a chimney flue?
To cut a vitreous chimney flue liner, you need a diamond blade mounted in an electric- or gas-powered saw. The surface of a diamond blade is impregnated with bits of actual diamonds, the only thing strong enough to cut through kiln-fired, ceramic clay. You’ll need to rent or buy the saw and blade.
Why is there a hole in my chimney?
One of the most common discoveries that historical homeowners often come across is a chimney thimble port; a circular hole in the wall used to house a thimble. The thimble enters the flue inside the chimney and is designed to accommodate a stovepipe.
Why is there a hole in my fireplace?
It leads to the ash pit. You brush the ashes into the opening and they fall into the ash pit, which part of the foundation of the chimney. Look in your basement or perhaps outside, and you should find a little metal door that allows you to clean out the pit if it ever gets full.
What is a Class A chimney system?
Class A chimney pipe has many names, often referred to as double-wall chimney pipe, triple-wall chimney pipe, all-fuel pipe, or insulated chimney pipe. Class A pipe is used to vent high-temperature exhaust released from wood, coal, and oil-burning appliances such as fireplaces, stoves, boilers, and furnaces.