Often asked: How To Secure A Bookshelf To The Wall?

How do you keep a bookshelf from falling over?

Fasten a furniture strap to the wall and the bookcase to keep it from tipping over. The straps cost about $6 at Target and hardware stores. Or, fasten the bookcase to the wall by driving 3-in. screws through the back of the bookcase (at obscure locations) into studs (be sure you hit studs).

How do you Anchor furniture to the wall?

Furniture restraints, also called anchoring kits, are typically comprised of two brackets tethered by a strap or cable. One bracket screws directly into the piece of furniture; the other fastens into a stud in the wall. The connecting strap or cable is typically affixed to each bracket, then tightened in place.

How do you secure furniture without putting holes in the wall?

QDOS Furniture Anti-Tip Kit



Consumers can affix a bracket to the wall with an adhesive and connect their furniture with tethers to keep fixtures secure. There are screws provided if one wishes to secure the supplied brackets to a stud in the wall. They should leave a hole no smaller than a picture hook.

You might be interested:  Question: How To Do A Retaining Wall?

How do you attach shelves to a wall?

Transfer to the Wall



Hold the level against the wall at the height you want the shelf. Remember that the top of the shelf will be above your marks. Adjust the level until the bubble is centered, and mark the keyhole locations on the wall. Then install anchors or drive the screws into the studs and hang the shelf.

How do you stabilize a bookshelf without backing?

If it has a backing, drive 3-inch screws through the backing into the studs behind the bookcase. Use washers with the screws to distribute the load. Alternatively, if there is no backing, affix 1-inch metal corner brackets to the studs and the underside of the top shelf or the sides of the bookcase.

How do you stabilize tall cabinets?

Attach a piece of wood the same thickness across the top back of the cabinet with screws and glue. Then screw inside the cabinet to the wall studs. This will keep the cabinet vertical and prevent things from falling between the wall and cabinet. Stain or paint board as needed.

How do you secure a dresser to the wall?

Dresser With a Solid Wood Back

  1. Move the dresser away from the wall.
  2. Run a stud finder over the wall at the dresser height to locate the studs.
  3. Move the dresser back to the wall.
  4. Take the top drawer out of the dresser.
  5. Drill a 3/16-inch pilot hole through the back wall of the dresser and into the wall through the stud.

Why should you anchor furniture?

Every 20 minutes, someone in the U.S. is injured due to an appliance, TV or piece of furniture falling over, according to Consumer Reports. It’s for this reason that anchoring your furniture to prevent tip-overs is one of the most fundamental steps you can take in rendering your home a little safer.

You might be interested:  Often asked: How To Make A Wall Frame?

Do you need to secure kallax to wall?

Mine is free standing and I never had any problems. However, I worked at Ikea and they do recommend you to mount the unit on the wall, especially if you have kids. The product comes with the brackets. You just have to buy the right fasteners for your wall in any hardware store.

Do you really need to attach Ikea furniture to the wall?

Though the instruction manuals that come with chests of drawers advise customers to secure their furniture to the wall using a bracket provided, not all do so, leading to tragic consequences. Ikea issued a safety warning, instructing all buyers to attach Malm chests to the wall to avoid other such accidents.

Do floating shelves need studs?

Ideally, you should attach floating shelves (or anything else you’re hanging) to a wall stud, as this will give you the most supportive base for your project. A stud finder—a hand-held device that uses a magnet to detect metal, such as the nails and screws in the wall studs of your home—can help you locate these.

How much weight can a drywall anchor hold?

Toggles, anchors or molly bolts are surprisingly strong. A 1/8 toggle can hold 30 pounds on 1/2-inch drywall and a 3/8-inch toggle can handle a hefty 50 pounds or more safely. When applying any kind of drywall anchor, you should understand how they work and which screw anchor may work best to put into a hollow wall.

Written by

Leave a Reply