- 1 How do you fish wire through a wall?
- 2 How do electricians feed wires through walls?
- 3 How do you run wire through ceiling joists?
- 4 How do you find wires in a wall?
- 5 How do I hide the wires to my wall mounted TV?
- 6 Can you run electrical wire behind studs?
- 7 Can you rewire a house without removing drywall?
- 8 How do you fish a HDMI cable through a wall?
- 9 How do you run a wire through a stud?
- 10 Can I run wire on top of ceiling joists?
- 11 Can you run two wires through the same hole?
- 12 How do you hide wires in an exposed ceiling?
How do you fish wire through a wall?
If your surround speaker is wall-mountable, then (see our note below) drill a hole in the wall so that you can duck the speaker cable in there and run it up the wall cavity. You will likely have to use a fish tape to pull the speaker cable up and through the bottom hole and out the surround speaker hole.
How do electricians feed wires through walls?
When adding or replacing wiring in finished walls, most electricians will attempt to make the horizontal portion of the cable run in the unfinished attic or basement/crawlspace areas, looping the cable down or up through the wall cavity, across the floor or ceiling joists, then vertically through another stud cavity to
How do you run wire through ceiling joists?
If you’re running parallel to joists, staple the wire to the inside of the joist every couple feet. The wire should be at least an inch away from the bottom edge (basically, if you ever cover it with drywall or some other ceiling, you don’t want people putting nails etc into the cable).
How do you find wires in a wall?
There are two kinds of stud finders that can help you find wires in a wall – magnetic and electric. A magnetic stud finder is used to detect metal nails in wall studs.
How do I hide the wires to my wall mounted TV?
Run TV Wires Behind the Wall
The best solution for keeping the cords of a wall–mounted TV out of sight involves hiding them behind the wall itself using recessed cable plates (e.g., Datacomm Cable Organizer Kit, available on Amazon).
Can you run electrical wire behind studs?
Yes, you can run the cable behind the studs. In these situations, you often see the electrician only drill a hole in every other stud and run behind the stud between. You can also afford to offset the drilled holes towards the back of the stud to get them even farther from possible damage from nails.
Can you rewire a house without removing drywall?
As most homeowners are concerned with the disruptiveness of the process, a question electricians get a lot is “can a house be rewired without removing drywall?”. The answer is usually yes, and even a whole house rewiring can in some cases be done with minimum disruption.
How do you fish a HDMI cable through a wall?
The simplest way is to unhook one of your existing cables and tape a string to the end. When you pull it out, you pull the string in. Then tape the HDMI cable along with the existing cable to the string and pull them both back in through the two horizontal studs.
How do you run a wire through a stud?
Drill into Corners at an Angle
- Angle the bit into tight spots.
- Make sure there’s at least 1-1/4 inches between the back face of the stud and the cable.
- Cover the face of the stud with a metal nail plate to protect the cable where the hole is closer than 1-1/4 inches to the face of the stud.
Can I run wire on top of ceiling joists?
There is nothing wrong with running your electric on top of joists but you really should try to do it in areas that aren’t going to be exposed to any foot traffic. If you need to go parallel then simply run them a few inches down on the side of a joist.
Can you run two wires through the same hole?
Don’t run phone lines, TV coax, or any other kind of signal cable in the same holes with the sheathed electrical cable.
How do you hide wires in an exposed ceiling?
You can hide wires in an exposed ceiling by painting the wires or your ceiling beams or using plastic or fabric cord covers, wooden molds, or decorative boxes. However, make sure your wires are safely in place to avoid any accidents. You can do this by pinning them in place, except when you’re using fabric covers.