Quick Answer: How To Light The Pilot On A Wall Heater?

Can I relight the pilot light by myself?

Pilot lights were once standard on all gas furnaces, but newer systems don’t always contain pilot light ignition systems. Instead, some newer furnaces use electronic ignition systems. Often, homeowners can relight the pilot themselves.

Why does the pilot light go out on my wall heater?

Pilot Goes Out



The heater won’t operate properly if the pilot flickers, is too weak or goes out, and the cause could also be blockages in the pilot tube. Another cause of a weak pilot is a faulty thermocouple.

How do you turn on an electric wall heater?

How to Start the Pilot Light on a Wall Heater

  1. Wall heaters are common appliances.
  2. In order for your wall heater to work, it needs a pilot light.
  3. First, find the selector dial on the heater.
  4. Next, Turn the selector dial until it reaches “pilot”.
  5. Push down on the ignite button.
  6. Alternatively, if there is no ignite button, follow these steps.
You might be interested:  FAQ: How To Tie Taekwondo White Belt?

How do you relight an automatic pilot light?

How to Relight an Automatic Pilot Light

  1. Set the thermostat on your furnace to its lowest setting.
  2. Remove the access panel covering the gas control knob.
  3. Turn the gas control knob to the OFF position.
  4. Turn the gas control knob or knobs to the ON position.
  5. Turn the electrical power to the furnace back on.

Is it dangerous if the pilot light goes out?

Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.

How much does it cost to relight a pilot light?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.

Will a pilot light stay lit with a bad thermocouple?

The job of the thermocouple is to keep the pilot lit. It does this by sending a tiny electric current to a sensor on the gas valve signaling the valve to stay open. Nothing lasts forever, and when the thermocouple wears out, the pilot won’t stay lit and your appliance won’t work.

Can a pilot light cause carbon monoxide?

A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.

You might be interested:  Often asked: How To Strengthen A Half Wall?

Should the pilot light always be on in a gas heater?

Leaving the gas on keeps this compound moving out of the tubes. Keeping the pilot light on will also keep moisture out of the unit and in turn, help prevent corrosion. As you can see, it’s probably best in most cases to extinguish the pilot light in your gas fireplace during the months when you don’t need heat.

Why is my wall heater not working?

If your heater’s not working at all, check for a tripped breaker or blown fuse. Reset the breaker or replace the blown fuse, if necessary. Remove the heater control knob, thermostat knob and faceplate to check for loose connections in these mechanisms. Tighten any loose wires.

What to do if your heat is not working?

Heater Not Working? 7 Troubleshooting Tips:

  1. Check that your thermostat is set to “heat.”
  2. Change the filter.
  3. Make sure the gas is on.
  4. Clear the chimney exhaust flue.
  5. Clean away leaves and debris from exhaust vents.
  6. Flush out the drain lines.
  7. Check for blocked ducts restricting airflow.

How does an electric wall heater work?

The appliance is installed on the interior walls. It basically consists of an electric element, a reflector, and a fan. As the element heats up, the fan circulates the heated air through the heater. The warm air is then transferred into the room through conduction.

How do I know if my pilot light is out?

The pilot gas line is a small metal tube below the burner assembly and distinctive by the slight upturn at the end. It will be apparent, if the pilot is lit, by the small blue flame burning at the end. If you do not see a small blue flame burning, the pilot light is out.

You might be interested:  Readers ask: How Far From Wall To Install Kitchen Can Lights?

Can you manually light a water heater with electronic pilot?

* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system.

Written by

Leave a Reply