Readers ask: How To Find Wall Studs Without Stud Finder?

What can I use if I don’t have a stud finder?

Look at the Trim



The baseboards in your home are attached to the studs. Check your baseboards to see if you can spot where it might have been nailed. These holes (commonly known as dimples) are usually painted over and filled with caulk. Despite this, you may be able to see one to locate a stud.

How can you tell where a stud is in the wall?

A good starting place is 16 inches from a corner. For better precision, use a tape measure and mark 12 inches, 16 inches, and 24 inches from the corner. Tap the wall at each distance. You’ll hear a solid sound when you tap the part of the wall that is supported by a stud.

Can’t find any studs in my wall?

There are several savvy ways to spot studs without any tool. Take a look at baseboard trim or crown molding. Baseboards should be attached to studs and if the spacing of nails is about 16 inches this might be the case. Spot the nails with your eye then knock on the wall directly above the nail location.

You might be interested:  Often asked: What Is Re-taekwondo?

Can I use my iPhone as a stud finder?

The iPhone beeps when its magnetometer, in the upper right of the phone, is near metal. Stud Find is an iPhone application that uses the device’s built-in magnetometer to find metal studs, screws, nails and anything metallic in a wall.

What is the best stud finder app?

Top 20 Stud Finder Apps For Android And iOS

  • Stud Detector. Stud Detector is one of the best stud finder app for android users which allows you to easily ind metal framing studs.
  • Stud Find.
  • Real metal detector with sound.
  • Wall Stud Finder.
  • Stud Detector by Guylyhey.
  • Metal Detector.
  • Metal Detector.
  • Toolbox.

Why do stud finders never work?

Most magnet type stud finders don’t work effectively since they are dependent on locating the fasteners (screws) used to secure the drywall and they can be very difficult to locate.

How far apart are wall studs?

The general spacing for wall studs is 16 inches on center, but they can be 24 inches.

Are outlets always on studs?

Most electrical boxes for switches or outlets are attached to a stud on one side. There are studs on either side of a window. Most trim (crown molding, baseboard, and shoe molding) is nailed on the stud.

Are studs always 16 apart?

Why You Should Find Studs



They’re always spaced either 16 or 24 inches on-center (measured from center to center) along the wall and run between the floor and ceiling. Drywall or lath (for plaster walls) attaches to the edge of the studs.

You might be interested:  Readers ask: How To Install Reclaimed Wood Wall?

Can’t find stud for TV mount?

If you cannot locate a stud, try tapping a small nail into the wall board near an existing fixture. If it meets resistance behind the wall-board then you have a stud. Wall studs should be spaced in regular intervals (usually 16″ on center in the US) so you can simply measure over to your mount area to locate them.

How do I find a stud with a magnet?

If you slowly slide a magnet along the surface of your wall, it will be attracted to the steel drywall screws that come up very close to the surface of the drywall. Even better, you can leave the magnet stuck to the screw to mark the stud throughout your project.

How do I know if I hit a stud?

How do you know if you hit a wall stud? Use a drill with the small bit, finish nail or screw. Power the bit or fastener through the drywall or plaster. If your on a stud you will feel resistance and see wood exiting when using a drill.

Can you download a stud finder?

Stud finder app for iOS and Android brings the simplicity and effectiveness of a real stud detector tool to your iPhone or Android device. The app uses your device’s compass (magnetometer sensor) to pinpoint metal studs, nails, and screws embedded in all wood wall studs.

Is there a stud finder that actually works?

If you’re hanging heavy pictures, mirrors, or shelves, you need to know where your wall studs are—and the best tool we found for the job is the C.H. Hanson 03040 Magnetic Stud Finder.

Written by

Leave a Reply