- 1 Where do you nail your tongue and groove?
- 2 Can you install tongue and groove over drywall?
- 3 Do you glue tongue and groove paneling?
- 4 How do you fasten tongue and groove pine boards?
- 5 What is cheaper shiplap or tongue and groove?
- 6 What is better shiplap or tongue and groove?
- 7 Is tongue and groove cheaper than drywall?
- 8 How much does tongue and groove ceiling cost?
- 9 What wood should I use for wall paneling?
- 10 Do you nail the tongue or groove?
- 11 How do you finish tongue and groove pine walls?
- 12 How do you attach a tongue and groove board?
Where do you nail your tongue and groove?
Avoid visible nail holes
- Install planks with the tongue up.
- Nail at an angle directly through the tongue and into your studs. You don’t need to nail through the face of the planks anywhere but on the bottom row and near the ceiling.
- Start with the bottom row first and work your way up.
Can you install tongue and groove over drywall?
Installing tongue-and-groove (aka T&G) boards is a fast, inexpensive way to panel any ceiling or wall. You can install T&G over bare framing, drywall or plaster, so it’s a great cover-up for an ugly ceiling.
Do you glue tongue and groove paneling?
+1 on no glue in the T&G joint. The individual boards need to be able to expand contract individually (That’s the advantage of T&G). To solve the exposed unfinished tongue issue, you can pre-stain and finish the tongues before assembly.
How do you fasten tongue and groove pine boards?
Fasten each board using a 2” 15 gauge nail on each joist. On the cut side, nail it 1/2” from the edge to prevent splitting the wood. On the tongue side, nail it through the tongue at an angle so the next row covers the nail.
What is cheaper shiplap or tongue and groove?
Shiplap is cheaper than tongue and groove, but it requires a bit more work on the carpenter to get the rows to lay flat against the building in a waterproof fashion. Also, if not installed properly, shiplap is more likely to warp and leak than its counterpart.
What is better shiplap or tongue and groove?
As a general rule, shiplap is the better choice for a very rainy climate, as its overlapping planks shed water quite well. Tongue and groove, on the other hand, can deteriorate in wet climates due to trapped water inside the interlocking connections.
Is tongue and groove cheaper than drywall?
One of most frequently asked questions is: Isn’t tongue and groove more costly than drywall? Generally, yes–the retail cost of T&G will cost you more than drywall. But the labor is where the cost comes down considerably, with regard to modular cabins.
How much does tongue and groove ceiling cost?
So, we know the tongue and groove ceiling looks awesome, but the big question is it affordable? According to the material you choose it can run anywhere from $2.00-$3.50 per square foot.
What wood should I use for wall paneling?
Wood is the traditional material used for wall panels but if you’re going for a more modern painted finish, MDF is much better value and is actually a very stable board. In high-moisture environments, like bathrooms, it’s essential to use Moisture Resistant (MR) MDF.
Do you nail the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
How do you finish tongue and groove pine walls?
Using an acrylic latex polyurethane, you can seal your tongue and groove pine paneling with a foam paint roller, brush, or paint pad. A paint pad cuts out bubbles and allows you to spread the polyurethane evenly and quickly, so it’s the recommended tool.
How do you attach a tongue and groove board?
Place the first board of the first row. Start at a far wall for vertical boards and at the floor for horizontal boards. Insert a 1/2-inch spacer between the board and starting edge. Run a bead of construction adhesive down the back of each tongue-and-groove board.