- 1 How do you prepare a tub surround for tile?
- 2 Where do you start when tiling a tub surround?
- 3 What can I put on the wall around my bathtub?
- 4 Do you install a bath before or after tiling?
- 5 How much space is needed between tile and tub?
- 6 How much does it cost to tile a tub surround?
- 7 Should tile be at the top or bottom of a shower wall?
- 8 Can I tile over drywall in a shower?
- 9 Where do you start when tiling a wall?
- 10 When tiling a shower do you start with the floor?
- 11 What is best board for bathroom walls?
- 12 Which is better fiberglass or acrylic tubs?
- 13 What can I use for shower walls besides tile?
How do you prepare a tub surround for tile?
Tub or shower wall tile preparation:
- Apply a layer of 1/2″ thick cement backer board to the wall studs.
- Tape any seams and corners with fiberglass tape.
- Apply thin-set adhesive over the fiberglass tape, and allow it to dry.
- Roll a waterproofing sealer over the walls, and allow the sealer to dry.
Where do you start when tiling a tub surround?
For a tub surround only, install the backerboard and tile 12 inches above the tub. When tiling around a tub, mark the first layout line at the vertical edge of the tile next to the tub. Follow the order shown in the diagram to snap the rest of the lines. If the tub is level, start with a full tile at its rim.
What can I put on the wall around my bathtub?
7 Waterproof Bathroom Wall Options
- Single-Sheet Plastic. You can buy single-sheet plastic for your bathroom walls in a variety of colors and styles.
- Acrylic. These are the most common waterproof bathroom walls.
- Stone. To achieve a high-end look, some people prefer to install stone walls in their bathrooms.
Do you install a bath before or after tiling?
Baths and/or shower trays are installed at 1st fix stage as they need to be fitted prior to the commencement of tiling. This is essential to get professional watertight seals, as water ingress resulting from doing things in the wrong order can cause massive problems later on.
How much space is needed between tile and tub?
Leaving a 1/16″ gap between the tub and tile will prevent the tile from cracking when the tub expands. Plus, a 1/16″ gap allows the caulk to properly fill the space and waterproof the transition between the tile and tub or shower.
How much does it cost to tile a tub surround?
The cost to tile a tub surround ranges from $750 to $1,500. This depends mostly on the material, which runs $0.50 to $15 per square foot. You’ll pay more for natural stone and less for ceramic.
Plan the Layout
The goal is to maximize the size of tiles at the bottom and top, avoiding narrow pieces. I avoid using a full piece at the top because the ceiling is usually not perfectly level. By cutting the top course of tile on all three walls, I can keep the joint width consistent all the way around.
Can I tile over drywall in a shower?
The bottom line is that drywall (and this includes moisture resistant drywall) should never be used behind tile in wet areas (showers and tub-shower combinations). This is especially important in a shower located on an outside wall, but also helps even if the shower is on an inside wall.
Where do you start when tiling a wall?
It’s always advisable to start tiling your grid in the centre of the wall, as it’s easier to make sure your pattern is symmetrical. It also means any half-tiles you may need can go at the end of each row and will be of matching size.
When tiling a shower do you start with the floor?
Professional tile installation generally utilizes a method where the tile wall hangs over the tile floor. The only way that this can happen without detailed planning and careful measurements is by installing the tile on the floor of the shower first.
What is best board for bathroom walls?
One of the best options for bathroom walls & ceilings is cement board. Cement doesn’t contain any organic matter for mold to use as a food source. Cement boards are usually sandwiched between two layers of fiberglass mesh, so there is no paper in the product.
Which is better fiberglass or acrylic tubs?
Acrylic is much more durable than a fiberglass tub. The chance of an acrylic tub chipping, cracking or fading is unlikely. Fiberglass tubs can fade and get cracked and scratched over time. Both styles can be cleaned with simple cleaning solutions.
What can I use for shower walls besides tile?
If you’re looking to mix it up a little with alternative shower materials, here are a few options to consider:
- Acrylic Panels. Acrylic shower panels offer a smooth and seamless look to your shower.
- PVC Panels.
- Stainless Steel.
- Stone Resin.
- Wood Shower Walls.